Search results

{{AC|front=AC 3-03|description=Description_AC3-03|testdata=Test Data_AC3-03|cfdsimulations=CFD Simulations_AC3-03|evaluation=Evaluation_AC3 =='''Best Practice Advice for the AC'''==

...6-07 Quality Review|bestpractice=AC 6-07 Best Practice Advice|relatedUFRs=AC 6-07 Related ACs}} == Best Practice Advice for the AC ==

{{AC|front=AC 4-01|description=Description_AC4-01|testdata=Test Data_AC4-01|cfdsimulations=CFD Simulations_AC4-01|evaluation=Evaluation_AC4 =='''Best Practice Advice for the AC'''==

{{AC|front=AC 4-04|description=Description_AC4-04|testdata=Test Data_AC4-04|cfdsimulations=CFD Simulations_AC4-04|evaluation=Evaluation_AC4 =='''Best Practice Advice for the AC'''==

{{AC|front=AC 6-02|description=Description_AC6-02|testdata=Test Data_AC6-02|cfdsimulations=CFD Simulations_AC6-02|evaluation=Evaluation_AC6 ...ameters are compared with experimental data. Comparisons with experimental data, including blade surface static pressure, and pitch-averaged static and tot

{{AC|front=AC 2-07|description=Description_AC2-07|testdata=Test Case_AC2-07|cfdsimulations=CFD Simulations_AC2-07|evaluation=Evaluation_AC2 An overview of the experimental test cases is provided here. The values of the [[DOAPs#PDPs:_Problem_Definition_

{{AC|front=AC 2-08|description=Description_AC2-08|testdata=Test Data_AC2-08|cfdsimulations=CFD Simulations_AC2-08|evaluation=Evaluation_AC2 The measurements outlined in the 'Test Data' section are well suited to assess whether they are reproduced by the simul

{{AC|front=AC 2-01|description=Description_AC2-01|testdata=Test Data_AC2-01|cfdsimulations=CFD Simulations_AC2-01|evaluation=Evaluation_AC2 ...e presented. For reacting flows, instantaneous temperature and composition data files are made available. Listings of the fluid mixtures used are given in:

...tion=UFR 3-07 Description|references=UFR 3-07 References|testcase=UFR 3-07 Test Case|evaluation=UFR 3-07 Evaluation|qualityreview=UFR 3-07 Quality Review|b = Test Case =

In the current application challenge (AC), ''in vitro'' velocity measurements using particle image velocimetry (PIV) ...n in the human upper airways” and provides the corresponding flow velocity data. The investigations were performed for steady-state inhalation at a flow ra

...6-07 Quality Review|bestpractice=AC 6-07 Best Practice Advice|relatedUFRs=AC 6-07 Related ACs}} Two international workshops, focused on this test case, have been organised: Turbine-99 - Workshop on Draft Tube Flow, Porjus

{{AC|front=AC 6-05|description=Description_AC6-05|testdata=Test Data_AC6-05|cfdsimulations=CFD_Simulation_AC6-05|evaluation=Evaluation_AC6- ...urbo_3D''' code, which was developed at UPMC/LEMFI, on fine grids of about 1.5 million points using the Launder-Sharma new-wall low-Reynolds-number k-ε

...6-08 Quality Review|bestpractice=AC 6-08 Best Practice Advice|relatedUFRs=AC 6-08 Related ACs}} ...one; border-bottom: solid windowtext 1.0pt; border-right: solid windowtext 1.0pt; padding: 0cm 2.8pt 0cm 2.8pt" width="89" valign="top" |

...publications). The boundary conditions applied at the inlet came from the data acquired during the experiment (2D cine PC-MRI). ...metry used in the calculation is the same as the one presented in the test data section. The computational domain has one inlet and one single outlet, so t

{{AC|front=AC 2-01|description=Description_AC2-01|testdata=Test Data_AC2-01|cfdsimulations=CFD Simulations_AC2-01|evaluation=Evaluation_AC2 ...conditions are specified with the same approach described in the previous test. The Flamelet database is obtained from the same reduced mechanism of the p

{{AC|front=AC 3-01|description=Description_AC3-01|testdata=Test Data_AC3-01|cfdsimulations=CFD Simulations_AC3-01|evaluation=Evaluation_AC3 ...1 of this report. The preliminary computational studies described in issue 1 had considered only the isothermal case. This enabled an early evaluation o

(shown in Fig.1) is a widely used test case for that the Sandia D Flame is not a demanding test case it seems to be

{{AC|front=AC 6-06|description=Description_AC6-06|testdata=Test Data_AC6-06|cfdsimulations=CFD Simulations_AC6-06|evaluation=Evaluation_AC6 =='''Best Practice Advice for the AC'''==

...vice. ''Access the Knowledge Base to find the UFRs associated with your AC''. In the present AC, experiments and simulations were conducted at a flowrate of 60 L/min throu

{{AC|front=AC 3-01|description=Description_AC3-01|testdata=Test Data_AC3-01|cfdsimulations=CFD Simulations_AC3-01|evaluation=Evaluation_AC3 ...predictions as well as through comparisons with the available experimental data.