Test Data AC4-03

From QNET
Jump to navigation Jump to search

Front Page

Description

Test Data

CFD Simulations

Evaluation

Best Practice Advice

Air flows in an open plan air conditioned office

Application Challenge 4-03 © copyright ERCOFTAC 2004


Overview of Tests

Once the office was built and occupied there was a short-term programme of monitoring internal temperatures. Measurements were taken over the whole diurnal cycle for several months during the spring of 2001. The CFD simulations were performed to assess overheating of the occupied space. However, the monitoring took place during spring time, so it was decided to focus on measurements made in mid afternoon on the hottest day of the monitoring, namely 25/04/01 at 16.00 hours. The measurements were designed to assess the comfort within the space, rather than to provide data for CFD evaluation. Nonetheless, from the suite of measurements that were taken, we have extracted data that are useful for CFD evaluation. The measurements that are used here are summarised in Table 1. The internal temperature profiles within the occupied zone, Tint, were used as DOAP in CFD evaluation.


Measurement Measurement Locations
Internal dry bulb temperature Three vertical profiles, on floors 2,3
Surface temperatures at all walls, floors and ceilings
Supply air temperature
External temperature


Table 1 Measured quantities used in the CFD evaluation

These measurements were made on the second floor, which had a profiled ceiling with a metal covering.

Three vertical profiles of internal temperature were measured at points A, A’ and B, which lie in two bays on the South West side of the building (see Figure 3 below). Measurements were taken at 5 heights, at z = 0.1, 1.1, 1.8, 2.8, and at the ceiling.

The occupants were asked to manually record when windows were opened, blinds were pulled down, and lights were switched on and off. However, there is no occupancy or activity log, i.e. the number of people present or the number of computers switched on was not recorded. The convective and radiative loads due to the occupants, machines and the lighting, can only be estimated, based on typical office use conditions. The loads have been estimated as follows:

• occupant loads - 1 person per 13m2 equivalent to 49 people in total at 35W (convective) each so occupant convective load is 1715W.

• machine loads 10W/m2 (assumed 100% convective) so total machine convective load is 6366W

• lighting loads 10W/m2 of which 55% is assumed to be convective, so that the total lighting convective load is 3500W.

Given the limited information it is not possible to quantify the errors associated with these estimates.

Test Case EXP-1

Description of Experiment

One of the bays has two measuring stations located, one next to a window (Station A) and one further in the space next to the central corridor (Station A’) see Figure 3. The other bay on the floor had one measuring station located next to the central corridor (Station B), where the measuring stations are marked with an X.


Image385.gif


Figure 3: Positions of measuring stations


Boundary Data

Air supply rate is not measured directly, but was taken from the Building Management System. The supply air temperatures were found to be similar to the external temperature, so for simplicity, one temperature was used for all inlets, equal to the external temperature.


Image460.jpg


Figure 4 - name and position of wall boundaries

Figure 4 shows the convention used to label the walls. The temperature values measured on each of the boundary surfaces and the external and inlet temperatures are shown in Table 2.


Boundary Temperature
NE1 24.0
NE2 24.0
NE3 24.0
SE1 24.0
SE2 24.0
SW1 24.0
SW2 24.0
SW3 24.0
NW1 24.0
NW2 24.0
floor 23.6
ceiling 24.7
19
19


Table 2 Temperatures measured at domain boundaries

The swirl diffusers were the Krantz 200mm diameter swirl diffuser, which has a ‘free open area’ of 0.18m by 0.18m.


Measurement Errors

The temperatures are all sensed using T type class 1 thermocouples and recorded using Intab AAC2 data loggers. This system has an accuracy of +/-0.2 °C. Calibration checks of the internal temperatures are being carried out at regular intervals with a sling hygrometer. The sling hygrometer was calibrated before use as were a small sample of thermocouples and channels on the Intab data loggers and digital multimeters. The external air temperature is measured to an accuracy of 0.2°C at 25°C.


Measured Data

The values of the measured internal temperature used to evaluate the CFD are shown in Table 3.


Height (m) Temp at A' Temp at A Temp at B
0.1 23.6 23.1 22.7
1.1 24.3 24.1 23.6
1.8 25 25 24.3


Table 3. Temperature profiles at the three measurement locations.


© copyright ERCOFTAC 2004


Contributors: Isabelle Lavedrine; Darren Woolf; Stephen Belcher - Arup

Site Design and Implementation: Atkins and UniS


Front Page

Description

Test Data

CFD Simulations

Evaluation

Best Practice Advice