UFR 2-13 Description: Difference between revisions

From KBwiki
Jump to navigation Jump to search
m (Dave.Ellacott moved page SilverP:UFR 2-13 Description to UFR 2-13 Description)
 
(122 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
=Fluid-structure interaction in turbulent flow past cylinder/plate configuration  I (First swiveling mode)=
= A fluid-structure interaction benchmark in turbulent flow (FSI-PfS-1a) =
{{UFRHeader
{{UFRHeader
|area=2
|area=2
|number=13
|number=13
}}
}}
__TOC__
__TOC__
== Flows around bodies ==
=== Underlying Flow Regime 2-13 ===
= Description =
==  Introduction ==
==  Introduction ==


Line 23: Line 30:
simulation tools are required.  
simulation tools are required.  


The long-term objective of the present research project is the coupled
The long-term objective of the research reported here is the coupled
simulation of big lightweight structures such as thin membranes
simulation of big lightweight structures such as thin membranes
exposed to turbulent flows (outdoor tents, awnings...). To study these
exposed to turbulent flows (outdoor tents, awnings...). To study these
complex FSI problems, a multi-physics code framework was recently
complex FSI problems, a multi-physics code framework was recently
developed~\citep{fsi-les-2012}. In order to assure reliable numerical
developed (Breuer et al., 2012) combining Computational Fluid Dynamics (CFD) and Computational Structural Dynamics (CSD) solvers . In order to assure reliable numerical
simulations of complex configurations, the whole FSI code needs to be
simulations of complex configurations, the whole FSI code needs to be
validated at first on simpler test cases with trusted reference
validated at first on simpler test cases with trusted reference
data. In~\cite{fsi-les-2012} the verification process of the code
data. In Breuer et al. (2012) the verification process of the code
developed is detailed. The CFD and CSD solvers were at first checked
developed is detailed. The CFD and CSD solvers were at first checked
separately and then, the coupling algorithm was considered in detail
separately and then, the coupling algorithm was considered in detail
based on a laminar benchmark. A 3D turbulent test case was also taken
based on a laminar benchmark. A 3D turbulent test case was also calculated to prove the applicability of the newly developed
into account to prove the applicability of the newly developed
coupling scheme in the context of large-eddy simulations
coupling scheme in the context of large-eddy simulations
(LES). However, owing to missing reference data a full validation was
(LES). However, owing to missing reference data a full validation was
Line 49: Line 55:
interacting with flexible structures.
interacting with flexible structures.


The present study is mainly related to two former investigation of Turek and Hron (2006,2010) and Gomes and Lienhart (2006, 2012) on vortex-induced fluid-structure interactions.
==  Review of previous work ==
The well-known 2D purely numerical laminar benchmarks of Turek and Hron (2006,2010) developed in a collaborative research effort on  
 
The present study is mainly related to two former investigations
of Turek and Hron (2006, 2010) and Gomes et al. (2006, 2012) on vortex-induced fluid-structure interactions.
The well-known 2D purely numerical laminar benchmarks of Turek and Hron (2006, 2010) developed in a collaborative research effort on  
FSI (DFG Forschergruppe 493) consists of an elastic cantilever
FSI (DFG Forschergruppe 493) consists of an elastic cantilever
plate which is clamped behind a rigid circular cylinder. Three different
plate which is clamped behind a rigid circular cylinder. Three different
Line 56: Line 65:
additional self-contained CFD and CSD test cases to check both solvers
additional self-contained CFD and CSD test cases to check both solvers
independently. These test cases were also used to validate the solvers
independently. These test cases were also used to validate the solvers
applied in the present study (Breuer et al, 2012).  
applied in the present study (Breuer et al., 2012).  
In order to close the gap of complementary experimantel and numerical data, a nominally 2D laminar experimental case
In order to close the gap of complementary experimantel and numerical data, a nominally 2D laminar experimental case
was provided by~\cite{gomes2006,gomes2013} and \cite{gomes2011b}. Here, a
was provided by Gomes et al. (2006, 2013) and Gomes (2011). Here, a
very thin metal sheet with an additional weight at the end is attached
very thin metal sheet with an additional weight at the end is attached
behind a rotating circular cylinder and mounted inside a channel
behind a rotating circular cylinder and mounted inside a channel
Line 68: Line 77:
demanding.
demanding.
There are also turbulent FSI benchmarks involving 2D structures:
There are also turbulent FSI benchmarks involving 2D structures:
in~\cite{stab-fsi-2008} a rigid plate with a single rotational degree
in Gomes et al. (2010) a rigid plate with a single rotational degree
of freedom was mounted into a water channel and experimentally studied
of freedom was mounted into a water channel and experimentally studied
by particle-image velocimetry (PIV). This study also presents the
by particle-image velocimetry (PIV). This study also presents the
Line 74: Line 83:
achieved by the present code for a turbulent FSI problem. As another
achieved by the present code for a turbulent FSI problem. As another
turbulent experimental benchmark, the investigations
turbulent experimental benchmark, the investigations
of~\cite{gomes2010,gomes2013} and \cite{gomes2011b} have to be
of Gomes et al. (2010, 2013) and Gomes (2010) have to be
cited: the same geometry as in~\cite{gomes2006} was used, but this
cited: the same geometry as in Gomes et al. (2006) was used, but this
time with water as the working fluid leading to much higher Reynolds
time with water as the working fluid leading to much higher Reynolds
numbers within the turbulent regime. The resulting FSI test case was
numbers within the turbulent regime. The resulting FSI test case was
Line 88: Line 97:
structural simulation and the grid adaptation of the flow
structural simulation and the grid adaptation of the flow
prediction.
prediction.
==  Choice of test case ==


Thus, in the present study a slightly different configuration is
Thus, in the present study a slightly different configuration is
Line 102: Line 113:
for the coupled problem) and the processing of the respective data to
for the coupled problem) and the processing of the respective data to
guarantee a reliable reproduction of the proposed test case with
guarantee a reliable reproduction of the proposed test case with
various suitable methods.
various suitable methods. A detailed description of the present test case is published in De Nayer et al. (2014).


== Description of the geometrical model and the test section ==
The described test case FSI-PfS-1a is a part of a series of reference
FSI-PfS-1a consists of a flexible thin structure with a distinct
test cases designed to improve numerical FSI codes. A second test case
thickness clamped behind a fixed rigid non-rotating cylinder installed
FSI-PfS-2a is described in Kalmbach and Breuer (2013). The geometry is
in a water channel (see Fig.~\ref{fig:rubber_plate_geom}). The
similar to the first one: A fixed rigid cylinder with a plate clamped
cylinder has a diameter <math>D \operatorname{=} 0.022m</math>. It is positioned in the
behind it. However, this time a rear mass is added at the extremity of
middle of the experimental test section with <math>H_c = H/2 \operatorname{=} 0.120m</math> <math>H_c/D \approx 5.45</math>, whereas the test section denotes a
the flexible structure and the material (para-rubber) is less
central part of the entire water channel (see
stiff. The flexible structure deforms in the second swiveling mode and
Fig.~\ref{fig:water_channel}). Its center is located at <math>L_c \operatorname{=}
the structure deflections are completely two-dimensional and
  0.077m</math> <math>(L_c/D \operatorname{=} 3.5)</math> downstream of the inflow
larger.
section. The test section has a length of <math>L \operatorname{=}  0.338m</math>
   
<math>(L/D \approx 15.36)</math>, a height of <math>H \operatorname{=}  0.240m</math>
----
<math>(H/D \approx 10.91)</math> and a width <math>W \operatorname{=}  0.180m</math>
<math>(W/D \approx 8.18)</math>. The blocking ratio of the channel is
about <math>9.2\%</math>. The gravitational acceleration <math>g</math> points in
x-direction (see Fig.~\ref{fig:rubber_plate_geom}), i.e. in the
experimental setup this section of the water channel is turned 90
degrees. The deformable structure used in the experiment behind the
cylinder has a length <math>l \operatorname{=}  0.060m</math> <math>(l/D \approx 2.72)</math>
and a width <math>w \operatorname{=}  0.177m</math> <math>(w/D \approx 8.05)</math>.
Therefore, in the experiment there is a small gap of about <math>1.5
  \times 10^{-3}m</math> between the side of the deformable structure and
both lateral channel walls.
The thickness of the plate is <math>h \operatorname{=} 0.0021m</math> <math>(h/D
  \approx 0.09)</math>. This thickness is an averaged value. The material
is natural rubber and thus it is difficult to produce a perfectly
homogeneous 2 mm plate. The measurements show that the thickness of
the plate is between 0.002 and 0.0022 m. All parameters of the
geometrical configuration of the FSI-PfS-1a benchmark are summarized
in Table~\ref{tab:geom_conf_bench}.
 
[[File:FSI-PfS-1a_Benchmark_Rubberplate_geometry0001.jpg]]


== Introduction ==
{{Demo_UFR_Desc_Intro}}
== Review of UFR studies and choice of test case ==
{{Demo_UFR_Desc_Review}}
<br/>
----
{{ACContribs
{{ACContribs
| authors=Michael Breuer
|authors=G. De Nayer, A. Kalmbach, M. Breuer
| organisation=Helmut-Schmidt Universität Hamburg
|organisation= Helmut-Schmidt Universität Hamburg (with support by S. Sicklinger and R. Wüchner from Technische Universität München)
}}
}}
{{UFRHeader
{{UFRHeader
|area=2
|area=2

Latest revision as of 12:10, 12 February 2017

Fluid-structure interaction in turbulent flow past cylinder/plate configuration I (First swiveling mode)

Front Page

Description

Test Case Studies

Evaluation

Best Practice Advice

References


Flows around bodies

Underlying Flow Regime 2-13

Description

Introduction

A flexible structure exposed to a fluid flow is deformed and deflected owing to the fluid forces acting on its surface. These displacements influence the flow field resulting in a coupling process between the fluid and the structure shortly denoted fluid-structure interaction (FSI). Due to its manifold forms of appearance it is a topic of major interest in many fields of engineering. Based on enhanced numerical algorithms and increased computational resources numerical simulations have become an important and valuable tool for solving this kind of problem within the last decade. Today FSI simulations complement additional experimental investigations. A long-lasting vision of the computational engineer is to completely replace or at least strongly reduce expensive experimental investigations in the foreseeable future. However, to attain this goal validated and thus reliable simulation tools are required.

The long-term objective of the research reported here is the coupled simulation of big lightweight structures such as thin membranes exposed to turbulent flows (outdoor tents, awnings...). To study these complex FSI problems, a multi-physics code framework was recently developed (Breuer et al., 2012) combining Computational Fluid Dynamics (CFD) and Computational Structural Dynamics (CSD) solvers . In order to assure reliable numerical simulations of complex configurations, the whole FSI code needs to be validated at first on simpler test cases with trusted reference data. In Breuer et al. (2012) the verification process of the code developed is detailed. The CFD and CSD solvers were at first checked separately and then, the coupling algorithm was considered in detail based on a laminar benchmark. A 3D turbulent test case was also calculated to prove the applicability of the newly developed coupling scheme in the context of large-eddy simulations (LES). However, owing to missing reference data a full validation was not possible. The overall goal of the present paper is to present a turbulent FSI test case supported by experimental data and numerical predictions based on the multi-physics code developed. Thus, on the one hand the current FSI methodology involving LES and shell structures undergoing large deformations is validated. On the other hand, a new turbulent FSI benchmark configuration is defined, based on the specific insights into numerical flow simulation, computational structural analysis as well as coupling issues. Hence, the present study should provide a precisely described test case to the FSI community for the technically relevant case of turbulent flows interacting with flexible structures.

Review of previous work

The present study is mainly related to two former investigations of Turek and Hron (2006, 2010) and Gomes et al. (2006, 2012) on vortex-induced fluid-structure interactions. The well-known 2D purely numerical laminar benchmarks of Turek and Hron (2006, 2010) developed in a collaborative research effort on FSI (DFG Forschergruppe 493) consists of an elastic cantilever plate which is clamped behind a rigid circular cylinder. Three different test cases, named FSI1, FSI2 and FSI3 are provided, complemented by additional self-contained CFD and CSD test cases to check both solvers independently. These test cases were also used to validate the solvers applied in the present study (Breuer et al., 2012). In order to close the gap of complementary experimantel and numerical data, a nominally 2D laminar experimental case was provided by Gomes et al. (2006, 2013) and Gomes (2011). Here, a very thin metal sheet with an additional weight at the end is attached behind a rotating circular cylinder and mounted inside a channel filled with a mixture of polyglycol and water to reach a low Reynolds number in the laminar regime. Experimental data are provided for several inflow velocities and two different swiveling motions could be identified depending on the inflow velocity. Owing to the thin metal sheet and the rear mass the accurate prediction of this case is demanding. There are also turbulent FSI benchmarks involving 2D structures: in Gomes et al. (2010) a rigid plate with a single rotational degree of freedom was mounted into a water channel and experimentally studied by particle-image velocimetry (PIV). This study also presents the first comparison between experimental data and predicted results achieved by the present code for a turbulent FSI problem. As another turbulent experimental benchmark, the investigations of Gomes et al. (2010, 2013) and Gomes (2010) have to be cited: the same geometry as in Gomes et al. (2006) was used, but this time with water as the working fluid leading to much higher Reynolds numbers within the turbulent regime. The resulting FSI test case was found to be very challenging from the numerical point of view. Indeed, the prediction of the deformation and motion of the very thin flexible structure requires two-dimensional finite-elements. On the other hand the discretization of the extra weight mounted at the end of the thin metal sheet calls for three-dimensional volume elements. Thus for a reasonable prediction of this test case both element types have to be used concurrently and have to be coupled adequately. Additionally, the rotational degree of freedom of the front cylinder complicates the structural simulation and the grid adaptation of the flow prediction.

Choice of test case

Thus, in the present study a slightly different configuration is considered to provide in a first step a less ambitious test case for the comparison between predictions and measurements focusing the investigations more to the turbulent flow regime and its coupling to a less problematic structural model. For this purpose, a fixed cylinder with a thicker rubber tail and without a rear mass is used. This should open the computation of the proposed benchmark case to a broader spectrum of codes and facilitates its adoption in the community. Strong emphasis is put on a precise description of the experimental measurements, a comprehensive discussion of the modeling in the numerical simulation (for the single field solutions as well as for the coupled problem) and the processing of the respective data to guarantee a reliable reproduction of the proposed test case with various suitable methods. A detailed description of the present test case is published in De Nayer et al. (2014).

The described test case FSI-PfS-1a is a part of a series of reference test cases designed to improve numerical FSI codes. A second test case FSI-PfS-2a is described in Kalmbach and Breuer (2013). The geometry is similar to the first one: A fixed rigid cylinder with a plate clamped behind it. However, this time a rear mass is added at the extremity of the flexible structure and the material (para-rubber) is less stiff. The flexible structure deforms in the second swiveling mode and the structure deflections are completely two-dimensional and larger.



Contributed by: G. De Nayer, A. Kalmbach, M. Breuer — Helmut-Schmidt Universität Hamburg (with support by S. Sicklinger and R. Wüchner from Technische Universität München)


Front Page

Description

Test Case Studies

Evaluation

Best Practice Advice

References


© copyright ERCOFTAC 2024